Hard disks are the least reliable component daily computer. As a rule, every day hard disks Proceed up to 3 times, after which they must be replaced. The worst in this situation are those who give up when they themselves are angry hard drive very difficult. Through this, important data is often lost among unsatisfied merchants. From which material we know how to check the hard drive for reference and correctly evaluate its capacity. Document No. 1. Checking the reference hard drive for help CrystalDiskInfo If you want to check your hard drive for normal use, the first thing you need to do is install the CrystalDiskInfo program. This cost-free program collects all available information about the hard drive and, on its basis, provides an assessment of its technical state. If the hard disk is completely referenced, then the body of the hard disk will be described as “Good”. How about hard drive If there are problems, then you will reject the “Anxiety” rating. Well, in these situations, when the hard disk is on the verge of death, the program receives a “Trash” rating.
You can also view the S.M.A.R.T output data in the CrystalDiskInfo program. (their vikoryst program for estimating will become), hot temperature disk, the number of times the hard drive is turned on, and the number of working hours. Work No. 2. We check the hard drive using the additional HD Tune program. It is also important to check your hard drive for damage. The easiest thing for anyone to do quickly cost-free program HD Tune (or її) paid version HD Tune Pro). Well, in order to be viconati reversal of the cruelty disk, launch the HD Tune program, go to the tab and press the “Start” button.
After finishing HD Tune, check your hard drive for reference. During the verification process, you can watch this process. Normal sections of the hard disk are shown in green, and damaged sections are shown in red.
On the surface of the hard disk, bad blocks are not at all to blame. Krok No. 2. We check the hard drive for legality manually. When testing with additional software, the hard drive can be checked for reference manually. To do this, just try to write a lot of different files (a couple of megabytes in size) to disk. For example, you can try copying a large folder of photos to disk.
If the test of writing the files is normal, try to test how the disk is running during the hour of reading data. To do this, try copying the data from the disk you are testing. Highlights: A regular hard drive can pass all three tests without any problems. The CrystalDiskInfo program has a “Garne” rating, the HD Tune program has no problems, and manual writing/reading tests can pass without problems. If everything is like this for you, then, despite everything, your hard drive is still working for a long time. But, naturally, there are no guarantees here and there are no guarantees. So the only way to reliably steal your data is backup copy. Your most important data (photos, videos, documents) is stored on a large number of hard drives.
How can I check my hard drive for damage?
We need the Victoria program. We create an image of the program for recording it on a disk here, or an image for a floppy disk here and write it on a disk (floppy disk).
Now we need to get hold of this disk (floppy disk) and restart the computer. And when you are on a computer or laptop, press F12 or Tab, you will need to launch the BOOT MENU. If nothing helps, try looking at the names of the keys at the bottom of the screen when you're interested, read the instructions to the motherboard. You can also go into the BIOS and select your first new device. To get to the BIOS, press Delet on your computer, on laptops and older computers F2. And then, on the first page, immediately after turning on the computer, this information is written at the bottom of the screen. The Bios menu varies slightly among different devices. Your data change the settings from your hard drive ( Hard Drive) on CDROM. Search the Boot device Priority, Boot or First boot device tab
In BIOS, you need to insert the CDROM (or Floppy Drive or floppy disk) on the very top row (using the +- or F5 F6 buttons). We save and reinstall the computer.
If you see Press any key to continue, press any key, after which the Victoria program will start.
Press the P key (English) and select the required channel, select using the arrows (if you don’t know what kind of disk you have, select it).
Press Enter and F2. Show up list hard disks(either several or one, since you only have one hard drive). If you don’t show up, press the P signal and select another channel.
I press the number that is written opposite required disk. and Enter. After we have selected the disk we need, let's move on to checking it for use. For this we press F4. Another small end appears, at this end we do not change anything and press Enter (you can read about the functions at this end in the instructions, which I will attach below). It will be a matter of checking your hard drive for trouble.
To the right upper codend You enter the numbers 5 ms, 20 ms, 50 ms, etc. This shows the hour for access to the skin sector on the hard drive. The more sectors with less attraction, the better. And the Defects tab will have bad sectors (those sectors where the hard drive is corrupted and no recording or reading is carried out at this place). If you have any defects, you will need a new hard drive. In principle, defects on the hard drive can be eliminated by replacing the hard drive (read the instructions for how to find out), otherwise I would not recommend any work because the hard drive is still available and you will spend all your and data.
You can also run the program under Windows, and it will work, but for this you need to download one of the ideas written below (download, extract to a folder and run):
- Enable (Current Panel > System > Hardware > Hard Drive Controllers) that IDE channel of the controller before you try the hard drive. This is necessary so that the program can easily access the HDD ports.
- You may not turn on the channel on the system, otherwise obsessed with Windows To which channel there is no reason to be connected (otherwise the OS, knowing the ATA device, will block the ports). If you have chosen this option, you must connect the hard drive after the system has been installed. Or, as an option, turn on life support until you try the hard drive only after the OS is fully installed (not all cheap life blocks can be tolerated)
- There is absolutely no point in turning on the hard drive in the BIOS, so that today’s multitasking operating systems do not need to go through the BIOS to check the presence of the HDD on the channel. You will need to install the driver. rice, for that , so that DOS itself does not flood this disk (and so that it does not spoil it in such a way that, theoretically, it can lead to conflicts between the OS and the program).
You can download the instructions here.
ps-land.ru
How can I check my hard drive through BIOS?
The hard drive is not the most important part personal computer And at the most inconvenient moment, this device can go wrong. To prevent this from happening, the HDD requires a continuous analysis of its usefulness and verification of the data recorded on new data for integrity. As a rule, this is what the fakhivs do, which means a bunch of speeches: they will definitely take you for a pittance and at some point the cruel ones will have to say goodbye. However, we have a little secret for you that you can simply check the size of your hard drive on your PC. This secret is hidden in the system BIOS.
Before the cob
Before we explain in detail how to check the hard drive from the BIOS for functionality, you should be aware of a number of speeches:
- This method cannot be used with solids hoarders SSD;
- Depending on the BIOS version, the names of menu items and their settings may vary significantly (or not).
Vlasna, that's all. Now let's go to Bios and see how we can diagnose the HDD.
Login to Bios
We have already talked about the middle part of the BIOS, its different types and adjustments, and for which we have seen a whole article. There, at one point, we were told how to get to the BIOS. Follow these instructions and become familiar with the Login section of the BIOS so that we can continue with you further.
Enables hard disk verification
Father, you are in the middle. Further, be very careful that the points that will be named in this article may look and be placed in a completely different way. Using the keyboard arrows to navigate, go to the Diagnostics section and select Primary Hard Disk Self Test. Assuming that your computer uses more than one hard drive, the system prompts you to select a disk to check from the available ones.
It will take about an hour to check the hard drive for corrupted sectors of the system. However, after completing this process, you can easily understand what is wrong with your hard drive:
- at a nearby test test whether your hard drive is damaged and will require repair or replacement;
- since the test of the book is 100% - everything is good with the HDD, and everything is different pardons for Zhorstky The disks will be corrected by the system.
Pouch
Using the BIOS tool as a tool for checking bad sectors on a hard drive, you can quickly diagnose the functionality of the hard drive on your computer. Of course, the problem here is present, and the visual difference of different versions of the BIOS is also obvious, as a result of which it is sometimes difficult to know which item is the same. Regardless of this, this method is very good, and you know about it, the skin is to blame.
chopen.net
Getting to grips with computers
As soon as a new hard drive is installed on your computer, the storage is not always recognized by the system. Once you make your connection, check the list of devices - but there is no disk there. In such a situation, you need to think about how to turn on the hard drive in the BIOS.
On the right, for a new storage device in Bios there may not be any adjustments made. For the disk to start displaying, you need to configure the correct system configuration. For whom:
- Start the computer;
- Before starting to install the OS, a screen will appear on the monitor where you can launch the BIOS. To complete this operation, you must press the DEL key, F2 or F11;
- Once logged into Bios, click on the “MAIN” row, then press the “Enter” button;
- In the menu that opens, you will see all connections to your PC, drives and disks. Select the required row and click on the new one;
- If you don’t find it, point to the SATA number you were connected to before, and then select the AVTO item. The sound of the disk starts to sound;
- When the system appears, select “save end exit”. The computer is re-invented;
- And now you can find your hard drive by clicking “Start”, then “My Computer”.
Checking the SATA connector
However, the disc may not appear. The obvious reason is that the SATA interface controller is enabled. To correct the situation:
- Go to Bios and find the “SATA configuration” item;
- On the "controller" tab, click "enable";
- Then vikorist the same algorithm of action as described above.
Activation of a previously disabled disk
Perhaps you enabled the hard drive in the BIOS. To activate it, you need to reset the settings. To do this, go to Bios and click on the “Load Default” row. After your PC is reinstalled, the disk is at fault. Go to “My Computer” and wonder what’s there.
Device Manager update
If the system “reboots” the disk, it will be necessary to update the information about connecting the device. For whom:
- Shutdown PC;
- Click on the icon "My computer" right key bears;
- Click on the “Power” item and open “Device Manager”;
- Press the mouse with the right button in the row where the name of the system is indicated (at the top of the window);
- Then click “Update configuration”. A scan will be made, after which disk is at fault will appear in the Device Manager.
If the disk does not want to appear, it is possible that the problem is not in the software components. To find out about it, do the following:
- Try connecting the storage device to another connector on the “mother”;
- Replace the cable to the interface, and also replace the cable to the life block;
- Before speaking, perhaps, the problem is the tension of the life block. It just doesn’t work, to indicate the Winchester. In this case, failures can occur in the first disk (on which the OS is installed);
- Connection for disk connection motherboard If you are using IDE-SATA connectors, replace them with something else. Pozhlivo, Tsomu has a problem;
- The hard drive may appear in the BIOS if the system has problems. Often in such a situation, the situation can only be corrected by fakhivet;
- If you have an IDE type storage device (SATA is the most important choice these days), you might think that the problem is the combination of old solutions with new ones. motherboard. This is not very good. If you want one IDE port on the motherboard, that means there is a suitable disk of this type in the system. Another thing is that the BIOS may have the remote function enabled. It is necessary to activate the “Award BIOS” parameter.
Checking the usefulness of the hard drive
Insha there could be a reason- Winchester simply doesn’t turn around. This is due to the fact that there is no sufficient life to reach the building or it will burn out during the day. To know for sure, write this:
- Open PC;
- Open the computer system unit by unscrewing the bolts on the side;
- Then pull the data cable out of the storage device. After this, the system no longer receives information about the need to save energy;
- Shut down the computer. Listen to the disc wrapper. Just to be clear, you may hit the hard drive – vibration may occur. If there is no vibration, this means the disk is not pressed;
- If you don’t want to understand exactly what the Winchester is, do this:
- Shut down the PC, listen to the disc;
- Open the computer;
- Pick up the PC power cable;
- Then pick up the hard drive's life cable;
- Insert the PC cable;
- Turn off the car and listen again. Then revive the life of the hoarder and listen again.
- Reverse the hard drive cable to connect it to another device, such as a disk drive.
- If nothing else helps, connect the storage device to another PC.
Does the disk still turn around without even starting to turn? Obviously, it’s out of order and just doesn’t work. Then you will need to replace it. Because hard drives cannot be repaired. Magnetic hard drives (HDD) can go out of order after one drop, so they need to be handled carefully so as not to damage the elements that collapse. In case of disks with the SDD standard, if a serious impact occurs, the disk will be lost in the working station, leaving fragments of its magnetic elements.
You can uninstall the hard drive in the BIOS and everything related to this operation independently. The new hard drive is recognized by the computer immediately. Maximum after adjusting the BIOS. If the cables are faulty, replacing them is difficult. If the disk is broken, you will need to get a new one.
comp-genius.ru
How to quickly check and update your hard drive to Usoy-Nauchim.ru
Computer becoming galmuvati? Do files and programs take a long time to open? Are any problems gradually resolved? This is all you can tell about a hard drive failure. How can we find out about the body of the hard disk? You will find out from this note.
Hello. Today I will tell you how to protest and also restore your hard drive.
In fact, the cause of malfunctions and malfunctions in your computer may be the hard drive. On the right is that the hard disk is constantly in operation. We permanently record information on it and then erase it. Data on the hard drive will be permanently overwritten. All this can lead to malfunctions in the robot. Ale yak viznati stan zhorstkogo disk?
For this purpose, many different programs have been created, one of which we will look at today. This program is called "HDD Regenerator". Why did I choose the program itself? But just because given the program It’s easy to do with Victoria, for example, to compare it with the “Victoria” program. Although, of course, the Victoria program has more capabilities, but it is easier to work with it. Today we are working with “HDD Regenerator”.
This program tests the hard drive, and also updates the bad sectors (zipped sectors). These are the main capabilities of this program.
You can use the program like Windows, so you can use it operating system, and under dos, without interfering with the operating system. Program management, however, is in both phases. The difference is less as soon as you launch the program. Below is a video in which I showed how to use the program with an advanced operating system, then here I will describe another option, and how to use the program with dos. Let's see.
How to get rid of HDD Regenerator
To get started you will need to install this program. The installation process is complicated, so I won’t describe it. After installation, you launched the program. A program window will open in front of you.
Whose work needs to be done in advance:
- Select " Zavantazhuvalna USB Flash”, press on the new one.
- Then you will need to select your USB device, the flash drive is to blame but is inserted into the computer. Select it and press “OK”.
- You will then be prompted for information, in which you simply need to press “OK”. The flash drive will be written to quickly, and you will be prompted to restart your computer (on my English). Click Yes, the computer will restart.
Now let's do this:
- When the computer is turned off, press and hold the F12 key. This is required to launch the "BOOT MENU". On some computers it runs differently than yours, look on the Internet as it runs on your computer.
- From the “BOOT MENU” select “USB-HD” (this item may look different, for example, “USB-HDD”).
- After that, I am interested in the program with which we work.
The program has opened and you are prompted to select the disk you want to scan. Select the required one by pressing the secondary key (number).
- Prescan - this option will show you the bad zones that stink.
- Normal Scan – this option will scan and update zipped sectors.
- Version Info – this is information about the hard drive.
- Scan and repair - this is scanning and updating.
- Scan, but do not repair - scan, but do not revive. Just show it to the poor sector.
- Regenerate – this option rewrites the entire disk, as there are no bad sectors.
I choose the first option and press “Enter”.
Now you need to select a sector for printing. I choose the first option to start scanning from the zero sector. I recommend that you do the same. We press one and stamp “Enter”.
The axis has begun scanning, and once the program has found the zipped sectors, it will renew them.
After verification, a window will appear.
To exit programs, press the Esc key. Another thing, often, after pressing Esc, a black screen appears with the input row. Just press the re-enable button on your system block. After re-enablement, do not press anything, Windows will auto-enable.
Axis and everything. You have learned to test and renew your hard drive. If not everything is clear, take a look at the video where I show you the process of scanning a hard drive. Please respect that Danish method It only helps in case of hard drive failures, but it is unlikely to help if, for example, you lost your hard drive under false pretenses, such as during physical exercises.
You can download this program on the Internet, and this program is also available on fancy flash drive We've done it before. Please note that this flash drive was mentioned...
Well, that’s where I’ll end this note. I hope this is cinnamon for you. Subscribe to the new blog and channel "PC Instructor"
Comments powered by HyperComments
vsemu-nauchim.ru
How to check the size of the hard disk
Hello dear readers of my blog! I will read this article and show you how to check the size of the hard drive; It doesn’t matter, hdd or ssd, 2.5” (on a laptop) or 3.5” (on a PC). Although he checks the fragments, he notes that the speed of reading and copying is lower than before, so one would play it safe for fear of wasting important data, and one would simply be out of cost. It doesn’t matter for any reason that you stuck with this food, it’s important, which program is the fastest and how.
Why does a hard drive break?
- Overheating The operating temperature of the HDD should not exceed 45 degrees.
- Hit. It is rarer on a computer. Most often, on a laptop with a strong sharp shutdown, transported in a workbench, or during an hour of work, if the windows hang, there is a lot of sound on the case.
- Primus's solution is to use buttons and sockets to replace the switch: Start - Complete work.
- That remains the term of exploitation. Everything breaks down early and late, so don’t be surprised by those who have a good eye.
Hard drive diagnostics
I won’t hide, I’ll say right away that the best program for checking your hard drive will be Victoria. And so, let's get started. Right now, download the Victoria program and install it on your computer. A shortcut to the installed utility will appear on your desktop. Run the track under administrator rights, for which the track will generate the following steps: hover over the Victoria shortcut, emboss right button Please, select “Run as administrator”, on Windows Vista, 7 and 8 you can set the request “Do you want to allow this program from an unknown vendor to make changes to this computer? - It’s stamped like this.
Good afternoon.
In today's article, I want to touch on the heart of a computer - a hard drive (too many people call the processor the heart, but I don’t really care that much. If a processor burns out, buy a new one, and there are no problems, if a hard drive burns out, then information in 99% of cases is not renew).
When do you need to check your hard drive for usefulness and sector size? It’s worth it, first of all, if you buy a new hard disk, but in a different way, when unstable robot computer: you have strange noises (); when downloading any file, the computer freezes; permanently copying information from one partition of the hard drive to another; Knowledge of files and folders, etc.
In this article, I would like to inform you in a simple way, how to check the hard drive for troubles, to assess its usefulness in the future, and to analyze the typical nutrition of the clients.
And so, let’s see...
Updated on 07/12/2015. Recently an article appeared on the blog about the renewal of bad sectors (recovery of bad blocks) by the HDAT2 program - (I think the message will be relevant for this article). The main feature of MHDD and Victoria is the support of virtually any disks with interfaces: ATA/ATAPI/SATA, SSD, SCSI and USB.
1. What do we need?
First of all, before the test operation, in cases where the hard disk is not stable, I recommend copying all important files from the disk to other media: flash drives, external HDD ta in. ().
1) A special program is required to test and update the performance of the hard drive. Similar programs If you want to get a lot of money, I recommend checking out one of the most popular ones – Victoria. Lower oriented posilannya on zavantazhenya
2) Next, a multi-color program window may appear: go to the “Standard” tab. The upper right part shows the hard drives and CD-Roms installed in the system. Select your hard drive that you want to test. Then press the Passport button. If everything goes well, then you’ll see how yours turns out zhorstky model disk. Div. picture below.
The hard disk controller works in AHCI modes(Native SATA) SMART attributes can be removed by seeing in the log notification “Get S.M.A.R.T. command… Error reading S.M.A.R.T!” About the impossibility of deleting SMART data, it is also worth mentioning that the letters “Non ATA” are illuminated when initializing the device; the controller does not allow the use of commands to the ATA interface, including the entry of SMART attributes.
In this case, you need to go to Bios and go to the Config tab ->> Serial ATA (SATA) ->> SATA Controller Mode Option ->> change from AHCI to Compatibility. After finishing testing with the Victoria program, change the settings as they were before.
You can read a report on how to change ACHI to IDE (Compatibility) in another article:
4) Now go to the Test tab and press the Start button. At the head window, left hand, orthocutaneous plants begin to appear, barred from different colors. Best of all, the smells will all be gray.
You need to show your respect for the red and blue rectilinear (that’s the name of the bad sectors, about them at the very bottom). It’s especially bad because there are a lot of blue orthocutaneous species on the disk, for which it is recommended to check the disk again, even with the “Remap” checkbox ticked. In this version, the Victoria program has identified bad sectors. This is how hard drives are being rebuilt, as they are starting to run erratically.
Before speaking, after such an update, the hard drive will not work for a long time. If I had already started to “get involved”, then I wouldn’t give in to the program. Due to the fact that there are a large number of blue and red orthocutaneous species, the time has come to think about a new hard drive. Before we speak, blue blocks are not allowed on the new Winchester! The confirmed correspondents call bad sectors (meaning trash that can’t be read). Such sectors that are not readable may fail both during hard drive preparation and during operation. Still, a hard drive is a mechanical device.
When working magnetic disks in the hard drive case they wrap tightly, and the heads move above them to read. When delivery, strike, I will arrange or program reprieve It may be that the heads are capped or fall onto the surface. In this manner, perhaps, singly, the bad sector will appear.
It's not scary, and on many disks there are such sectors. File system The production disk isolates such sectors using the file copy/read operation. In the future, the number of sectors may increase. However, as a rule, the hard drive fails more often for other reasons, most notably the bad sector. So the very bad sector can be isolated for help special programs, one of whom we met in this article. After such a procedure, the hard drive begins to perform more stable and faster, however, it is unknown how long it will take to achieve this stability...
With the best…
A hard drive is a storage device where all computer information is saved. It is also important to keep an eye on the HDD and regularly carry out diagnostics in order to quickly spot problems. This is ideal, but until problems with storage devices are resolved, computer users often don’t know how to diagnose hard drive performance, and this is absolutely necessary. If your computer and information on it have any significance for you, take the time to read the guide, which will help you find out how to verify robot zhorstkogo disk for additional help, without wasting a lot of time.
We check the feasibility using Windows methods
If you don't have enough time or knowledge to use the special software needed to diagnose the HDD, you can quickly use what's included in Windows from the start. Simple ideas:
Go to the HDD through Explorer or the “My Computer” shortcut.
Right-click on the accumulator icon, then select “Authority” from the menu.
On the page that appears, go through the “Service” tab, located at the top. Click the “Recheck” button.
Wait until the program is in place and stop checking the usefulness of your hoarder.
It's a pity Danish method not as effective as diagnostics using special software - you can only order corrections and adjust the procedure to a more serious scanning of sectors. To thoroughly scan and eliminate malfunctions and repairs, a more serious approach is required.
We scan the HDD with third-party software
Programs, with the help of which you can find out about the presence of Winchester lesions, as well as deal with their detection, are very rich, and learn the instructions for drying the skin from them - it is very long and complex. For these reasons below, you can become familiar with the way in which the vikoristan transmits popular programs Victoria. Choose another security software Remember that the operating principle of disk diagnostic programs practically does not vary from program to program. Axle instructions for Victoria:
Run the program as an administrator by clicking the menu for additional RMB on the program shortcut.
In the program window at the top, find the Standard tab and click on it.
on new page You will see a list of substances detected by your system - located at the top right side of the program. Select HDD, then press the Passport button. If you have done everything correctly, and it is accessible to the user, Victoria will immediately inform you about it.
Go to the SMART tab, which is usually expanded from the tab you previously opened. Here you need to select Get SMART and check out the praise on the side of the program.
Go to the TEST section, then press the START button to start diagnosing your HDD.
During the Victoria verification process, the HDD is displayed as a grid of squares. Gray squares indicate that everything is good - for normal work, the possession of such squares may be important, but most of all sectors are important. Red squares are damaged sectors that hang like dead weight and respect the hoarder’s robots.
If you have blue squares - sectors that cannot be read, they need to be scanned again from Victoria with Remap mode enabled.
Now you know how to change your nose.
Remember that as time passes, unreadable sectors on the disk accumulate more and more - they appear as a result of mechanical deformations, intense memory decay, and other reasons. This is a normal phenomenon and can be changed from the old ones.
Share this article with your friends so that they can also learn about it and learn to independently diagnose HDD defects. Don't forget to pay in advance for renewal so you don't miss out on the availability of new products!
Experienced users are well aware that the performance of a hard drive can be affected by minor impacts, for example, voltage surges, mechanical faults and shocks, static voltage, etc. The hard disk mechanism itself can destroy the surface of the storage device, where information is stored. Below is a guide on how to correctly check your computer's hard drive for reference.
The main symptoms of a damaged hard disk
As soon as you start your PC, you can make loud noises or hear sounds like crackling. Such noise should immediately alert the user of the computer and worry about diagnosing the hard drive. It is recommended that before testing this important element of your PC, you copy all the important and specific files to an external device or another computer, so that the test itself can be transferred to the hard drive.
It is absolutely necessary to clean up before starting the program to check, to ensure good cooling of the hard drive, for example, open the cover of the system unit case and clean the internal parts of the saw that have accumulated. There is a lot of grinding noise when the hard drive is functioning because its head is damaged, which means there are bad sectors. If you don't keep up with the inputs, then their number of incremental growth can lead to the loss of the HDD's usefulness.
Verification procedure
The engineers have developed a lot of different special utilities for testing the usefulness of this important element of the PC. The same procedure can be performed using any of the installed Windows tools.
From stocked Windows tools
The operating system allows you to analyze the hard drive. This method is not very reliable, but it’s hard to use it. By analyzing the surface of the hard drive, OS features can be corrected and corrected.
The algorithm of the sequence of actions consists of the following stages:
Using the Seagate SeaTools utility
A significant number of computer users have already helped solve the problem with this manual program. It is cost-free, completely Russified and effectively copes with the diagnosis of hard drives of most manufacturers. For more information, it is available on the resource "seagate.com".
The program is equipped with an intuitively understandable interface. Once you open the utility, you will immediately transfer hard disks from which you can run all the necessary tests. As a result, a signal will be displayed, and the main program can generate updates to the faulty sectors. 
The addition can be expanded freely, but only applies to the possession of one specific vibrator. Western Digital" However, fragments of the stench are widespread in the Russian Federation, and this program can help a significant number of people.
The functionality is similar to the description of the program. You can install it from the official resource "support.wd.com".
Allows you to not only perform a cost-free check of a broken HDD, but also view detailed S.M.A.R.T. information, as well as create great quantity Various tests of ownership.
In addition, the utility works effectively with flash drives, RAID, SSD.
The following report will be based on this program, which will ensure high accuracy of test results at this time. The utility is available for installation on the page "softportal.com".
It is necessary to perform the following follow-up actions:
Note: It is not recommended to check the "Erase" box, as this will erase all files. 
Visnovok
The hard drive is one of the weakest parts of a modern computer. The primary term of its exploitation does not outweigh the five rocks, but rather clearly indicate exact hour awkward.
Therefore, the only way out is regular inspection and diagnosis.