Very often, iPhone owners turn to our service with the same questions: what to do if the iPhone screen moves away from the body (frame), there is a gap (backlash) between the screen and the iPhone body? Now we will try to answer.
First, let's look at the system for attaching the display module on the iPhone to the metal case of the smartphone.
The fact is that, starting with the iPhone 5, the device is disassembled from the side of the display. Those. to get to the internal components we need to first remove the display module. The screen itself is glued to the plastic frame with special fasteners. These fasteners fit into grooves on the body.
When a person says that the screen is moving away from the body, there can be three options:
1) The screen departs precisely from the plastic frame, which sits quite tightly in the body.
2) The screen, together with the plastic frame, does not fit snugly against the smartphone body.
3) A combination of the first and second options (which is extremely rare).
Why is this happening?
A wide variety of physical and chemical factors affect the phone during use. iPhone is used in hot, cold, and rain. Liquids are spilled on it and subjected to mechanical stress. What your "apple assistant" does not have to go through. And all this cannot but leave traces on him.
Now let's look at the causes and consequences of each of the cases:
The screen comes off the plastic frame.
As mentioned above, the iPhone display is glued into a frame that attaches to the body of the smartphone.
This glue, although it holds well, like any other glue, loses its properties over time and under the influence of external factors. The screen begins to "float", as it were, when you press on it at the gluing point. There is a gap. At first it may be barely noticeable, and you most likely did not pay attention. At this stage, it is often quite good to warm up the display and press it against the frame (we do not recommend doing this yourself, there is a risk of killing the screen). Over time, moisture gets into the gap between the plastic and the glass, dust and dirt get clogged. And then the button began to sink, or the battery began to discharge quickly. Accordingly, it became necessary to disassemble the iPhone. (Do you remember that he understands from the screen?). A mechanical effect was added, which accelerated the peeling process. (If initially nothing goes anywhere, then, in the process of repairing the iPhone, nothing will come off. Therefore, do not rush to scold the master). Very often the reason lies in the curved case or "swollen" battery. What is the bottom line? The longer you delay the repair, the worse the consequences can be. So, for example, if your frame is too loose, it catches the display backlight, the backlight, in turn, also comes off
(glued on the back of the screen on a special double-sided tape and consists of several light-scattering layers).
Dust, debris, moisture gets under the backlight and between its layers. On the screen it looks like black dots in the back of the display, streaks.
From now on, you need to change not only the frame, but also the backlight.
Suppose no repairs were made. What will be next? And then, when the screen moves away from the frame well enough, it will hang on the display cables (which, by the way, are very delicate and are afraid of any impact.) As a result, problems with the sensor and / or the image will begin. Now the screen can only be thrown away ...
Another variant. The problem has already been started, but you yourself, or somewhere you were offered to glue the frame. And it’s good if “super-moment”, “101 glue” and their analogues are not used for these purposes. Because if in the future you need to replace the frame, you will only be able to tear it off together with the paint on the display. As a result, the glass will have to be changed.
Also, the glue can get under the backlight of the display, as a result of which, again, only the replacement of the backlight (if this is not a "super-moment" otherwise it is a replacement of the screen). But even if everything turns out well, it is not known how long this whole thing will last before it peels off again (after all, dust and dirt cannot be removed well).
The most optimal and competent option is to replace the frame with a new one. Factory hot glue has already been applied to it. To replace such a frame, special equipment is required. With careful adherence to the gluing technology, high quality and durability of service is ensured.
The screen, together with the plastic frame, does not fit snugly against the body of the smartphone.
And again, as mentioned above, the iPhone display is glued into the frame, which is attached to the body of the smartphone. Sometimes these mounts break. There may be several reasons: firstly, this often happens when the iPhone falls on hard surfaces, and secondly, when the device is carelessly disassembled (sometimes with neat, but due to the fact that the frame has come off the screen, it loses its rigidity and is impossible without certain efforts to disassemble the device, although this is more related to the third option: "The screen moves away from both the frame and the body"). There is only one way out - to change the frame to a new one.
It so happens that the grooves on the case, into which the frame fasteners are inserted, relax. Most often due to the frequent disassembly of the apparatus. This problem is solved by pressing the grooves or replacing them.
And the most common reason is the curvature of the body. Due to the nature of the metal alloy of which the case is composed (sometimes called the "back cover"), it cannot be aligned. It is very brittle. In addition, it is simply physically impossible to make it perfectly even again. The solution is obvious - to replace the case.
The consequences are very commonplace. With a small backlash, nothing bad will happen. Moreover, in rare cases, even on new iPhones, this defect occurs. (Although it is better to try to pass it under warranty. Who wants an imperfect new bull's eye?) With serious gaps, anything can get inside your phone and here the consequences are very difficult to predict.
Finally, please remember one simple thing. If your iPhone screen has moved away from the body and at the same time the battery is swollen or the body itself is bent, distorted, bent, etc. then no glue, no special equipment and nothing at all will help you until you replace the case.
By the way, by clicking on the link, you can find out all that interest you
How to stick glass on iPhone?
Additional protective glass for your phone is a modern alternative to the usual screen films. This accessory will protect your smartphone from all types of mechanical damage to the display (scratches, abrasions, cracks from the device falling).
If you've decided to purchase a protective glass for your iPhone, here are some basic tips for choosing this accessory:
- the thickness of the glass determines the level of protection of the phone from drops and shocks;
- choose the type of glass - matte or glossy. The second option is cheaper. Glossy products protect the screen from bumps, but not from scratches;
- the matte glass fully protects your iPhone from bumps, scuffs, drops and glare.
Installing a protective accessory on your phone screen does not require any special skills. Let's take a closer look at how to stick a protective glass on an iPhone in a few simple steps.
Step 1. Cleaning the display
Clean up your workplace. Make sure there is no dust on the surface, which may eventually remain under the film. Then open the packaging and place all items on a clean, flat surface.
Clean your smartphone screen with a cloth and glass cleaner. Dry the display surface thoroughly and wait until it dries completely. This action will remove even invisible dust particles. Try not to touch the iPhone screen itself anymore, so as not to create new streaks and dust particles. The wipes for the initial cleaning of the phone come with a protective glass.
Step 2. Unpacking the protective glass
In the next step, unpack the accessory and prepare it for sticking to your phone. Take the screen and peel off the protective layer, which, after gluing, will be in contact with the phone display. After detaching the protective layer, try not to touch the protective glass, otherwise fingerprints will remain on the product.
Step 3. Bonding
Turn the protective glass over with the side that was released from the film down. Place the accessory above the smartphone screen without touching it. Try to match everything as evenly and accurately as possible to avoid uneven gluing.
Further action must be done very quickly. Gradually apply the glass to the iPhone display from the top to the bottom. Let go of the film so that the side sections adhere to the phone by themselves. Due to good cleaning of the display, bubbles will not form.
Step 4. Smoothing the surface
Users do not always know how to stick glass on an iPhone. As a result, the result may not be perfect. To remove small irregularities or trapped air, take a piece of microfiber (included with the glass) or a clean cloth and gently wipe the phone, moving from the center of the display to the sides, applying light pressure. In this way, flaws can be eliminated.
A film is also glued to the outside of the protective glass. Remove it immediately after eliminating any flaws. Now turn on the device and check the sensor responsiveness. Normally, the additional screen should not affect the smartphone in any way.
Eliminate errors
If too much dust and dirt gets under the protective glass during gluing, it will be inconvenient to use the smartphone. The sensor may react worse to touch, and the appearance of such a phone will not be the best. Many users are wondering how to re-glue glass on an iPhone and can it be done at all? Yes, you can.
If the accessory does not adhere properly the first time, carefully detach it from the display and set it aside on a clean surface. Wipe the iPhone screen thoroughly again and make sure there is no more dust or dirt on it. Only after cleaning the screen, stick the glass again. You shouldn't peel off the accessory anymore.
How to remove glass from iPhone?
Typically, users only need to remove the protective glass when it breaks during a fall or impact. It is very important to remove the accessory correctly so that fragments do not damage the main display of the smartphone.
Take a plastic card and pry it off the edge of the protective glass. Then slide the card under the glass until it is completely removed. This method allows you to create a kind of barrier to the display and the damaged protective accessory.
Among the additional accessories for smartphones, protective glass is perhaps the most necessary component, as it protects the gadget from mechanical damage. Many owners of mobile devices of such a popular brand as Apple give significant sums of money for new models of phones, and of course everyone buys a protective glass to minimize the risks of damaging an expensive device. In this small review, we want to answer the user's question of how to glue a protective glass on an IPhone.
Be sure to prepare a clean work area and tidy your hands, they must be perfectly clean. Wipe the screen of the device with a special tissue and place the phone in front of you. Now remove the protective film from the glass to expose the adhesive layer. If we are talking about replacing the protective glass, then after removing the old material, dried glue will remain on the screen, it will not be easy to remove it. Moisten a cotton pad with pure alcohol, wipe gently, slowly, wipe the matrix surface with translational movements. Do not overdo it, if you press too hard, you can damage the device, then, to replace the touchscreen, you will have to contact an Apple service center.
- Remember, the most important thing is not to touch the glass with your hands after you have removed the protective film from it, otherwise your fingerprints will remain on the adhesive side, which will ruin the appearance of the gadget.
Jewelry accuracy in the process of gluing the glass is extremely important, all edges must match the iPhone screen, so take your time so as not to ruin everything. So, peel off the film from the protective glass and match it to the screen without touching the surface. Now you need to quickly glue the middle of the glass, the edges should lie on their own, you just have to smooth it out. Due to the fact that we have cleaned the surface, bubbles should not form, that is, you can count on a perfectly flat mirror surface of the iPhone.
How to glue the protective glass yourself onIPhone, and what are the cons
It is not difficult to stick a protective glass if you follow all the above rules, but such an additional accessory implies certain disadvantages. First of all, it should be noted that the weight of the iPhone will increase, as will the dimensions, if this does not bother you, then feel free to glue the protection against mechanical damage to the gadget.
Many iPhone owners try to treat the device as carefully as possible. For this, various covers, bumpers and protective glasses are bought.
Here we will tell you how to easily and quickly glue the protective glass without "defects" in the process.
How to do it
Remove the iPhone case before gluing the screen protector. If the iPhone display is already covered with old film or glass - feel free to remove it. Wash your hands thoroughly to avoid getting dirt on the screen.
It is best to glue in a well-lit place to see every speck that hits the screen of the device. Well, choose the cleanest possible surface for the glass sticker.
Let's get started
Step 1... Cleaning up the iPhone display.
For this we use any microfiber cloth so as not to leave anything superfluous on the screen.
You can also use an alcohol wipe and then wipe the display with a microfiber cloth with a soft cloth.
Step 2... Additionally, we clean the smartphone screen using the bundled tape or any other sticker.
Just touch the display with tape and lift it back up. The adhesive surface will collect dust residues.
Step 3... Now you need to remove the protective film from the adhesive side of the glass and attach it to the screen.
Important: Hold the glass by the edges so as not to leave unnecessary marks on it.
Step 4... Place the glass gently on the iPhone screen.
If the glass is good, it will fit on the smartphone screen by itself. But for greater confidence, you can smooth it yourself.
We run our finger through the center of the smartphone and start smoothing until all bubbles are removed. If there are any small bubbles left, take a plastic card and, using light pressure, slide it over the areas where the bubbles form.
In this tutorial, we used mocoll glass... And it's not just that
When you sadly look at an iPhone whose display is covered with a pitiless mesh, it's too late to think about protection. The manufacturer of protective accessories Mocoll has taken care of the consumer in advance.
All brand products are built in such a way that the buyer spends a minimum of time gluing the protective glass.
Considering that the Chinese brand Mocoll () has been producing protective glasses for several years, the company's engineers have thousands of hours spent in research laboratories.
Glasses are produced using high-tech equipment and in the process of processing they obtain a number of important properties. Mocoll glasses:
- Are only thick 0.33 mm... The glass is homogeneous and of equal thickness at any point. Mocoll has one of the lowest manufacturing tolerances among glass manufacturers.
- Mocoll glasses can easily withstand the impact of sharp objects and do not shatter into fragments on impact.
- Hardness at 9H on the Mohs scale. Only diamond is higher.
- The glasses have an oleophobic coating, so after gluing you will not feel any tactile changes from interacting with the iPhone screen.
- Mocoll supplies its products with a rich package. The set has everything you need to stick on glass without additional purchases and the search for a piece of cloth or a plastic card to eliminate bubbles.
Mocoll has several options for safety glasses at once. 2.5D, 3D and advanced development - 3D glasses with elastic edges to match the color of the device body.
As you can see above, installing Mocoll safety glasses is very easy. Due to the presence of a special silicone layer, you can not worry about the appearance of hated bubbles during gluing.
For every taste, color and wallet
Despite the high quality of materials used in the manufacture of modern gadgets, there is a need to protect them from shocks, falls or moisture. This is very important for users of the IPhone line. After all, everyone knows that Apple products are expensive, they need care, no one wants to accidentally destroy, for example, two monthly salaries in a few seconds.
Fortunately, manufacturers have taken great care to create accessories that keep devices safe. So, to protect the screen, special films or protective glasses are provided. The latter, in turn, are presented to the buyer with different thickness parameters.
How to stick protective glass on iPhone?
Of course, you can stick on the protective glass directly in the store when you buy it. However, this is not always convenient, and some stores provide such services for a fee. Although it is small, you can still do this work yourself:
- First you need to remove the cover from the smartphone (if any);
- If there is an old screen protector, it should be removed;
Open packaging with new glass. Usually wipes are supplied with the device. One for degreasing, it contains alcohol, and the other for removing dust from the display;
- Use an alcohol-containing cloth to wipe the screen;
- Second, remove streaks and dust;
- Take the glass out of the packaging and remove the sticker from it.
- Align the glass at a distance using the button and speaker;
- Gently lower the glass onto the display.
If after this procedure air remains under the glass, it can be removed with a plastic spatula. However, if there are microscopic bubbles, you should not worry, they will come out on their own after a while.
If dust gets under the glass, then you need to bend the glass from the side of the damaged area and carefully remove the dust with adhesive tape. Then again you need to press everything back. If this is the first time you do this and you are unable to do it, then you should not worry, the procedure takes practice, even if the first pancake does not despair.
In general, this work takes several minutes. However, the result of such efforts is fully justified. With glued protective glass on your iPhone, you don't have to worry about scratching or chipping your screen.
How to apply protective glass to your iPhone screen